View and Download Polaris RANGER owner’s manual online. RANGER Offroad Vehicle pdf manual download. Also for: Ranger 6×6 , Ranger Related Manuals for Polaris Ranger RZR EFI. Utility Vehicle Polaris Ranger EV Owner’s Manual For Maintenance And Safety. (68 pages). View and Download Polaris Ranger HD owner’s manual online. Polaris Sales Utility Vehicle Polaris Ranger RZR EFI Manual. ( pages).
|Published (Last):||19 March 2015|
|PDF File Size:||11.38 Mb|
|ePub File Size:||4.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
After opening a bottle of brake fluid, always discard any unused portion. Ranger xpRanger 6x6Ranger crew.
Polaris RANGER 800 Owner’s Manual
Headlight and poalris lenses become dirty during normal operation. Page 57 Refer to the Gearcase Specifications Chart on page 49 for recommended lubricants, capaci- pklaris and torque specifications. Inspect the bearings housing. The fill plug is located on the side of the gearcase just below the shift lever bell crank. Shift weights should not be changed or altered without first having a thorough understanding of their positioning and the effects they may have on belt to sheave clearance, clutch balance and shifting pattern.
Rear Caliper Mounting Bolts: Grease the joint with the special joint grease provided in the Replace the drive clutch assembly if shaft bushing. This manual also for: Clean rsnger, repair or replace as necessary. The engine is off. Apply Polaris All Purpose 5. Spring Preload Adjustment The front and rear rangwr have a preload adjustment. Turn the key to the ON position.
Use Bushing Tool PA This will ensure proper sealing when Flywheel Nut Torque installing bolts. If the fuel pressure is out of specification, replace the fuel pump assembly.
Owner’s Manuals | Polaris RANGER
Remove the dipstick and fill the sump with two quarts 1. Do not allow these types of products to contact the vehicle. The VIN can be found stamped on a portion of the front left frame rail, close to the left front wheel see Figure Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart.
All segments including the fuel icon will flash.
Remove PTO end engine mount. The solenoid actuates an engagement dog, which locks and unlocks the rear differential. Electrical circuits are off, except Acc, 12V.
Remove the old spring and install a new one. The ignition switch must be replaced if all keys are lost.
Polaris Ranger Manual | eBay
Install a NEW circlip on the end of the shaft. Remove the transmission input shaft from the housing.
Allow the water to drain completely. A collision or rollover can occur quickly, even during routine maneuvers like turning, or driving on hills or over obstacles, if you fail to take proper precautions. Loosen the hose clamp between the throttle body and intake Transmission Transmission Fluid ml Check the following items when shifting difficulty is encountered: Page 7 cc H. If necessary, apply them lightly several times to let friction dry out the pads. Use the strap adjusters to tighten any loose straps.
Never turn at high speeds. Apply RTV silicone sealant to outside edge of inner clutch cover-to-engine seal, to ensure a water tight fit between the seal and the cover.
When operating on slippery surfaces such as ice or loose gravel, reduce speed and use extra caution to reduce the chance of skidding or sliding out of control. After immersion, always take the vehicle to your dealer service. Pivot the A-arms upward and rear hub carriers downward Engine Removal Remove the 2 push rivets from the rear of the center console.
Follow the instructions on the container for the recommended amount.
22010 to remove ALL debris when replacing the belt could result in vehicle damage and severe injury or death. Replace if damage Push upper pad retainer pin inward and slip brake pads past is evident or if worn beyond service limit. Do not install it in any other product.
Polaris Ranger 800 HD Owner’s Manual
At this point the reflash process will begin. Use the following instructions to dry it out before operat- ing.
Inspect the ring gear and differential gears for chipped, worn, or broken teeth. Bearing cup is a ranget. Spare fuses are provided in the fuse box. Install new seals on each side of the gearcase housing using a standard seal installer or other suitable method.
Press shaft into the new bearing.