CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Dujora Tojakazahn
Country: Niger
Language: English (Spanish)
Genre: Education
Published (Last): 26 January 2007
Pages: 124
PDF File Size: 16.31 Mb
ePub File Size: 17.45 Mb
ISBN: 284-2-88631-454-9
Downloads: 86260
Price: Free* [*Free Regsitration Required]
Uploader: Vudozilkree

confguration A poorly designed network with discontiguous subnets could have problems with connectivity if the summarization feature is left on. Advertises directly connected networks classful address only. The remote subnet Houston config exit Returns handboik privileged mode.

The topology consists of four routers and some of you may have noticed that the topology is the same that we used for multi-area OSPFv3 configuration earlier in the chapter, and also uses identical IPv6 addressing scheme. The show ipv6 eigrp topology command provides more detailed topology information about the subnet, as shown below:. One incoming global distribute list One outgoing global distribute list One incoming interface distribute list One outgoing interface distribute list One outgoing redistribution distribute list.

The commands used to set these parameters have to be used confiyuration global configuration mode.

EIGRP Configuration| Step By Step Guide

Function EIGRPv4 EIGRPv6 Create routing process and assign ASN global configuration mode router eigrp asn ipv6 router eigrp asn Define router ID explicitly router configuration mode eigrp router-id rid eigrp router-id rid Change number of multiple routes to same subnet router configuration mode maximum-paths num maximum-paths num Set the variance router configuration mode variance multiplier variance multiplier Set interface bandwidth and delay to influence metric calculation interface configuration mode bandwidth value delay value bandwidth value delay value Change hello and hold timers interface configuration mode ip hello-interval eigrp asn time ip hold-time eigrp asn time ipv6 hello-interval eigrp asn time ipv6 hold-time eigrp asn time Enable EIGRP on an interface network ip [ wildcard-mask ] router configuration mode ipv6 eigrp asn interface configuration mode.

Related Articles  ETICA EN LOS NEGOCIOS CONCEPTOS Y CASOS MANUEL VELASQUEZ PDF

You may use the show ipv6 eigrp interfaces command to verify if EIGRPv6 has been enabled on correct interfaces:. Home Guides About Blog Shop.

Creates an incoming global distribute list that refers to access control list ACL 1. Creates a standard ACL number 10 and explicitly denies the HULL config-router distribute-list 30 out eigrp No neighbor adjacency will be formed. Set interface bandwidth and delay to influence metric calculation interface configuration mode. Houston config-if ip address We will use the topology consisting of four routers as shown in Figure for this example.

EIGRP Configuration With Packet Tracer ⋆

Houston copy running-config startup-config. Topology entry for Austin config-keychain-key send-lifetime Houston eigtp key-string tower Identifies the key string. The rest of the configuration simply enables EIGRPv6 on all interfaces using the ASN to associate with the interface, using the ipv6 eigrp asn command. You should carefully review the configuration for each router shown above.

The subnet is reachable via next-hop link-local IPv6 address FE It can be applied to external type 2 and external type 1 routes but not to intra-area and interarea routes. If the parameters do match, the two routers become neighbors and each router adds the other to its EIGRPv6 neighbor table, as listed with the show ipv6 eigrp neighbors command. Austin config-if ip address The subnet has one successor, which has an FD feasible distance of The objective is to prevent networks NOTE If a path is not a feasible successor, it is not used in load balancing.

Related Articles  LIBRO BIOLOGIA DE LOS MICROORGANISMOS BROCK PDF

Router config router eigrp Creates routing process Router config-router network Austin config-keychain-key exit Returns to global configuration mode. As a result, the rest of the routers in the topology will not be aware of the subnet and will confiugration be able to route packets to the subnet.

Houston config-keychain-key exit Returns to global configuration mode.

Houston config-router key chain eddie Identifies a key chain name, which must match the name configured in interface configuration mode. Houston config-keychain-key send-lifetime Austin config-router key chain susannah Identifies a key chain name, which must match the name clnfiguration in interface configuration mode.

cinfiguration EIGRP automatically summarizes networks at the classful boundary. Router config-router passive-interface default. Austin config-if ip authentication key-chain eigrp susannah. Router config-router distribute-list 2 out.

13-4 EIGRP for IPv6

Identifies a key chain name, which must match the name configured in interface configuration mode. Router config-router network R4 configure terminal Enter configuration commands, one per line.

Houston config-router no auto-summary Disables auto-summarization. Without it, an administrative distance of 5 is automatically applied to the summary route.

See All Related Articles. As a result, networks There are lot more similarities than differences, so it makes sense to list the few differences that exist between the two protocols. Austin config-router cojfiguration auto-summary.