Lead Small Outline Integrated Circuit (SOIC), JEDEC MS, Wide. DM74LSSJ. M20D. Lead Small Outline Package (SOP), EIAJ TYPE II. 74LS, 74LS Datasheet, 74LS Octal Bus Transceiver Tri-State Datasheet, buy 74LS, 74LS pdf, ic 74LS Details, datasheet, quote on part number: . IC VOLTAGE DETECTOR V TO Specifications: Output: Open Drain or Open Collector ; Reset: Active.
|Country:||United Arab Emirates|
|Published (Last):||2 August 2005|
|PDF File Size:||7.3 Mb|
|ePub File Size:||13.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
SN , Tube SN; Röhre SN ID, IC – Integra
Return to the synopsis. By observing the LED and the bill-posters kc, check the correct operation of the meter by consulting the table of figure You thus noted that L1 can be ordered independently of the buffer which, not validated, does not intervene.
By commenting on the experiment, one can say that each stage of the meter carries out a division by two of the frequency of the signal applied to its entry ; if one injects the signal with iic Hzcoming from contact CP1at the entry f 1 of the meter, the various exits, one obtains signals whose frequency is each time reduced by half. The figure b represents the diagram of the electric circuit carried out. After the sixteenth clock pulse, the incrementing of the indication of the bill-posters starts, this one being in hexadecimal code, of 00 to finish to FF at the end of counting.
IC 74LS/ DIP20 (end 7/4/ PM)
The entry RESET gives the meter to zero, it is asynchronous ; as soon as a level H is applied to him, the meter passes to 0. On the twelve exits of Q1 with Q12one finds a number binary of twelve bits active of: L and that, for this reason, it must be fed with a stable tension of 5 V. To carry out the following experiments, it will be necessary to use lc meter.
The electric diagram of the circuit carried out is represented figure b, while the figure c represents its synoptic diagram. The most significant bit M. Electronic forum and Poem.
Static page of welcome. Carry out then the connections necessary. Indeed, when SW0 is in position 1the passage of the signal in the direction of A8 with B8 is authorized.
A higher tension could damage it.
Now reverse the direction of transmission by applying the rectangular signal provided by CP1 to the B8 entry. L1 ignites with its full intensity.
IC 74LS245/74245 DIP20
Forms maths Geometry Physics 1. Will finally know that the circuit 74LS is a circuit of technology T. L0 and L1 flicker then at the rate of 10 Hz. Indeed, L0 still flickers, ordered by the signal coming from CP1 ; on the other hand L1 does not flicker any more.
To contact the author. It is thus enough to a little attention to observe the phenomenon and if there would remain some points obscure, do not hesitate to start again several times the experiment. Observe what occurs on A8. Of course, it is not a question to hope the clock pulses up to to check the table: Operational test of a Meter on 12 floors. As you can note it, the frequencies spread out of 5 Hz with 0, Hzi.
To carry out the experiments envisaged in this practice, it will be necessary for you to use the following material: Form of the perso pages. The door of entry NAND is followed of a trigger of Schmitt who is used to improve quality of the signal, then come two reversers which control the chain of dividers. You can notice the sign represented inside each buffer ; it indicates that the buffers used comprise a circuit of re-arrangement of the trigger type of Schmitt.
Electronic forum and Infos. It is about the CDbinary asynchronous meter with 12 bitswhose synoptic diagram is represented figure In this first phase, you will check the operation of the one of the eight 7245 buffers of the integrated circuit. High of page Preceding page Following page.